How exactly do you distinguish between stamped parts and sheet metal parts?
I. Core Definitions
1. Stamped Parts
Parts produced by cold stamping of metal sheets using stamping dies and presses.
Processes involved include: blanking, punching, bending, drawing, flanging, forming, riveting, etc.
All parts manufactured with stamping dies can collectively be referred to as stamped parts.

2. Sheet Metal Components
Sheet metal refers to the general term for cold-forming processes of sheet materials, which are divided into two main categories:
1) Die-stamping forming (classified as stamping parts);
2) Moldless manual/CNC processing: laser cutting, CNC bending, grinding, welding, and free bending on press brakes.
Summary in one sentence:
Sheet Metal Parts are a broad category, while stamped parts are a subset of sheet Metal Parts that are mass-produced using molds.
Relationship: All stamped parts belong to sheet Metal Parts, but sheet Metal Parts are not necessarily stamped parts.

II. Core Difference Comparison Table
1. Processing Methods
- Pressed parts: Produced in batches using fixed steel molds on a press machine. Includes blanking dies, bending dies, and stretching dies.
- Ordinary sheet Metal Parts (non-pressing): Laser cutting, CNC bending, welding. No need for dedicated molds; only general equipment is used.
2. Production Volume
- Pressed parts: Mass production, with annual output of tens of thousands or hundreds of thousands of pieces, which helps to spread the cost of molds. Small batches are not cost-effective.
- Sheet Metal Parts: Small batches, single pieces, prototypes, non-standard equipment enclosures. Can be made with just a few dozen or several hundred pieces.
3. Plate Thickness Range
- Pressed parts: Can be made in various thicknesses. Thin materials (0.5mm) for household appliance shells, thick materials (6-12mm) for automotive structural components, and also stretch deep tubes.
- Regular sheet Metal Parts: Mostly made from thin sheets, typically ranging from 0.8mm to 6mm; deep stretching and complex forming are difficult to achieve through free bending.
4. Complexity of Forming
- Pressed parts: Capable of deep stretching, concave and convex forming, complex curved surfaces, special-shaped flanging, high-precision forming, with extremely high shape freedom.
Examples include automotive shells, fuel tanks, nut brackets, and stretched shells.
- Free sheet metal processing: Can only perform flat plates, simple bending, and hole drilling. It is difficult to perform stretching and concave/convex forming, which are complex shapes.
5. Cost Composition
- Pressed parts: The initial mold cost is high, but the material cost per unit is extremely low. The cost becomes cheaper as production increases.
- Sheet metal components: There is no mold cost. The labor and machine time costs are high, and the unit price is expensive. The more the production volume, the less cost-effective it becomes.
6. Dimension Accuracy
- Pressed parts: The mold is fixed, and the dimensional consistency is extremely high, with good interchangeability, making them suitable for batch assembly.
- Bending sheet Metal Parts: Each bending operation has a slight error, and the batch consistency is weaker than that of pressed parts.
III. Illustrative Examples, Easy to Understand at a Glance
Typical stamped parts:
Automobile frame shell, fuel tank, hardware support, motor housing, stretching tube parts, household appliance inner liner.
Must be produced by die stamping and stretching molding.
Typical sheet Metal Parts (without molds):
Equipment cabinet, electrical control box, protective cover, machine frame shell.
Laser cutting of sheet + CNC bending + welding molding, no molds required.
Cross sections:
Small-sized hardware bending parts, can be produced by mold stamping for mass production, or single-piece prototyping by bending machine. It can be both sheet Metal Parts or stamped parts.
IV. Engineer's Selection Suggestions
- Production volume of thousands or tens of thousands, complex shapes, with stretching concave-convex structures → Make molds for stamping parts to reduce single-piece costs.
- New product prototyping, small batch of dozens of pieces, simple flat bending shells → Directly make sheet metal laser + bending, eliminating the high cost of molds.
- Thick sheet materials, deep stretching, complex curved surface molding: Can only use stamping process, ordinary sheet metal bending cannot achieve.

