Leave Your Message


News Categories
Featured News

Sandblasting, shot blasting, and grit blasting

2026-06-16
  • 1. Sandblasting: Precise and Flexible

    The sandblasting process uses compressed air as the main power source, spraying irregular abrasive materials at high speed onto the surface of the workpiece. The core principle is "cleaning + precise roughening", which also takes into account deburring. It is a key pre-treatment process for subsequent spraying and electroplating.

    The power can be flexibly adjusted. The pressure for the pressurized sandblasting is 0.5 to 0.7 MPa, while for the suction sandblasting it is 0.3 to 0.5 MPa. In some scenarios, high-pressure water flow can be used as an auxiliary (wet sandblasting). The medium used is irregular abrasive materials with sharp edges, such as quartz sand, brown corundum, and eco-friendly walnut shells, etc. The particle size is selected based on the surface roughness requirements. For Sa2.5 grade rust removal, G120 to G80 particle size is recommended.

    图片1.png

    The main objective is to thoroughly remove oil stains, old coatings and rust from the surface of the workpiece, precisely control the surface roughness, enhance the adhesion of subsequent coatings, and also be applicable for art carving and matte treatment of electronic products. It is suitable for small batches, multiple varieties and complex-shaped fine workpieces, such as molds, thin-walled aluminum parts, and local rust removal of ship sections. It is more friendly to soft metals and thin plates, avoiding deformation. It complies with the GB/T8923.1 rust removal grade standard.

    2.Shot Peening: Precise Focus

    Shot peening is similar in power form to sandblasting, using compressed air or a small centrifugal force as the power source. It sprays circular projectiles at high speed onto the surface of the workpiece. The core focuses on "surface strengthening", making it suitable for local treatment of complex parts.

    The main function is to enhance the

    surface hardness, fatigue resistance and wear resistance of the workpiece through cold hardening. It also takes into account stress correction and deburring. The cleaning effect is weaker than that of sandblasting. The applicable scenarios include local strengthening of key load-bearing components such as automotive gears, aviation parts, and bearings. It should be noted that if there is oil on the surface of the workpiece, it is necessary to remove the oil in advance to avoid contamination by the projectiles and affect the effect

    20Shot Blasting: High Efficiency in Batch Processing

    Shot blasting is powered by mechanical centrifugal force. Through the high-speed rotating impeller (blasting head), circular projectiles are rapidly ejected onto the surface of the workpiece. Its main features are "high-efficiency batch cleaning + surface strengthening", with a high degree of automation. It is the preferred choice for large-scale production.

    In terms of power, the impeller rotation speed can reach 1500 - 3000 r/min, and the initial velocity of the projectiles is up to 100 m/s. It does not rely on an air compressor. The energy efficiency over a long period is better than the other two processes, and the efficiency is improved by more than 30% compared to manual sandblasting. The medium used is circular, non-angled projectiles, such as cast steel balls, stainless steel balls, etc., with a diameter of 0.8 - 2.5 mm. They can be recycled hundreds of times and only need to be replenished regularly (replenishment volume ≤ total volume 10%).

    图片3.png

    The main function is to automatically remove the oxide scale, sand and rust from castings and forgings. At the same time, it enhances the surface hardness and fatigue resistance of the workpiece through cold hardening, and eliminates internal stress. The applicable scenarios mainly involve large quantities of regular workpieces, such as steel plates, wind turbine towers, and automotive chassis components. It can be combined with an automated conveying line to achieve continuous production. It complies with the JB/T8355 equipment standard and the GB/T8923.1 rust removal grade standard.

     

    The differences between sandblasting, shot blasting and shot peening

    • Differences in Power Sources
    • Sand Blasting: Mainly powered by compressed air, the air pressure can be flexibly adjusted to meet different precision requirements;
    • Shot Peening: The power source is similar to sand blasting, and it can use compressed air or a small centrifugal force, allowing for precise control;
    • Shot Peening: Utilizing the centrifugal force of the impeller (mechanical power), it does not rely on an air compressor and has more stable and powerful power.

    Core Target Differences

    • Sandblasting: The core objective is to clean the surface of the workpiece and precisely roughen it, serving as a pre-treatment step for subsequent spraying and electroplating, while also addressing deburring.
    • Shot Peening: The core is to strengthen the surface of the workpiece locally, enhancing its hardness and fatigue resistance, with a relatively weak cleaning effect.
    • Shot Blasting: The core is to systematically clean the rust and oxide scale from the surface of the workpiece, achieving overall surface strengthening, with a focus on high efficiency.

    Differences in Medium Characteristics

    • Sand Blasting: Uses irregular and sharp-edged abrasive materials (such as quartz sand, brown corundum), with no recyclable value;
    • Shot Peening: Utilizes round projectiles, resulting in smooth surfaces and minimal damage to the workpiece, and can be recycled;
    • Shot Blasting: Consistent with shot peening, both using round projectiles (such as cast steel balls, stainless steel balls), with high recycling efficiency.
    1. Application Scenarios Differences
    • Sand Blasting: Suitable for small batches, multiple varieties, and finely-shaped precision parts (such as molds, thin-walled aluminum parts);
    • Shot Peening: Suitable for complex internal cavities and edge corners that cannot be covered by shot blasting, mostly used for critical load-bearing components (such as automotive gears);
    • Shot Peening: Suitable for large-scale production of regular parts in large quantities (such as steel plates, wind turbine towers), and can be combined with automated production lines.

    Environmental Protection and Cost Differences


    • Sand Blasting: Produces a large amount of dust, and the abrasive cannot be recycled. The long-term cost is relatively high;
    • Shot Peening: Produces a medium amount of dust, and the shot can be recycled. The cost is between sand blasting and shot peening;
    • Shot Peening: The equipment is fully enclosed, resulting in less dust, and the shot has a high recycling rate. The long-term cost is the lowe
  •